Waveshare Ethernet Module, High-Performance 10/100 Ethernet Physical Layer Transceiver (PHY)

Product Information

EDIT: After reading that the lenght of wires can be an issue at 50MHz, I wired it with 10cm wires (instead of 20cm on the photo), still the same. The entry: #define D_ZIGBEE_NOT_STARTED "Zigbee not started" is duplicated in i18n.h from all language files. This produces a warning while compiling due to redefinition if changing the language in my_user_config.h

I will add my opinion. Rejecting a RMI support in new ESP32 series like S3 is a very bad decision. Now I cannot to achieve high network performance. When I used LAN8720 with old chip, I could achieve up to 60Mbit/s in useful throughput. But now if I forced to use some SPI bridges like Wiznet W5500, it allows me only 15Mbit/s throughput. Of course, I can use Wiznet W5300 with parallel interface, that gives me 80Mbit/s network performance, but this chip is enough expensive in comparison with W5500 or LAN8720 and much bigger in their case. Espressif have published some code for the TLK110. But it is relatively expensive (around 6 EUR when bought in small quantities) and is relatively big as it has an MII-interface which is not entirely needed. The LAN8710A/LAN8710Ai connect to the MAC layer using a variable voltage, digital standard MII or RMII interface,These devices support HP Auto-MDIX†, employ Microchip's proprietary flexPWR ® technology andare available in both extended commercial (0°C to 85°C) and industrial (-40°C to 85°C) temperature range options. iBeacon (xdrv_52): Clean up BLE_ESP32 based driver; add commands and advert timing. Remove HM10 code - it's in the other one.....

10/100 Base-T/TX Ethernet Transceiver with RMII Interface

Power and mode must be individually controllable. Some devices may not function properly if the mode is also turned off when the power is turned off. Add command ``L1MusicSync <0|Off>|<1|On>|<2|Toggle>, 1..10, 1..100>`` to control Sonoff L1 Music Sync mode sensitivity and speed ( arendst#10722) my knowledge is not so deep to understand if Olimex has more feature than the proposed cheaper device ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR Technology in a Small Footprint

When STM become officially supports external PHY Ethernet, I will delete this repository. Hardware requirements

Parametrics

the advantage could be that if wifi is not good we can use lan cable, maybe it could be PoE powering? Remove the two jumpers from CN2, and place them at the two outermost empty jumper pins marked CN11 and CN12.

emac: Timed out waiting for PHY register 0x2 to have value 0x0007 (mask 0xffff). Current value 0xffff emac: Timed out waiting for PHY register 0x3 to have value 0xc0f0 (mask 0xfff0). Current value 0xffff Microchip'sLAN8720A/LAN8720Aiarehigh-performance, small-footprint, low-power 10BASE-T/100BASE-TX transceivers specifically designed for today's consumer electronics, industrial and enterprise applications. The LAN8720A/LAN8720Aiare the industry's smallest footprint solutions with up to 40% lower power consumption than existing Microchip transceivers. The LAN8720A/LAN8720Ai have an integrated voltage regulator and ESD protection components to help reduce Bill of Material (BOM) costs. I wanted to have only Ethernet connection due to my wifi problems (that was the reason I chose esp32)Zibee add ``SetOption120 1`` or ``ZbEndpointTopic`` to add the endpoint as suffix in topic when using ``SetOption89 1`` BUT when I turn wifi off (wifi 0 in console or changing wifi configuration to non existing wifi), I also loose Ethernet connection. While we're certainly not thinking of dropping Ethernet for future products, at this point we do not have any publicly announced upcoming chips with Ethernet in it. (I cannot comment on if the feature is in not-yet-announced chips, sorry for that.) Note that you could always add e.g. a SPI Ethernet chip to an ESP32-S3 to get Ethernet connectivity, although I agree that is not as optimal as simply having an integrated MAC.